To ensure your safe operation, please strictly in accordance with the provisions of this manual.
This manual is copyrighted and may not be copied, cut, or modified without permission. Once found, the company will retain the contents of the manual without prior notice
Product Overview
Thank you for purchasing the DC bruhsless motor advertising barrier gate. This product adopts the latest mold design technology, mold die-casting manufacturing technology, double-row five tension springs balance design, long spring life, good tensile flexibility. Brushless control speed regulation technology, no clutch design, more reliable quality, more convenient to use, the movement adopts two-stage worm gear transmission, curved crank arm and three connecting rod structure, UP&DOWN is fast and stable. Easy maintenance and long service life.
Length type of the boom and operating Speed Parameters
Functions
1. The running speed can be adjusted from 3sec to 10sec.
2. Open the barrier by the motor wheel when the power is off. Automatically reset when power on.
3. Curved crank arm three-link movement structure,operation stable
4. Wireless remote control open and close.
5. Arm auto reverse( force adjustable)
6. Infrared photocell is available
7. Loop detector is available
8. Connect parking management system open, close signal.(request open and close signal)
9. Traffic light port(2A12V/220VAC, less than 40W traffic light can be used)
10. Offering limit signal for car parking management system( output COM/NO/NC)
11. Delay closing arm function
12. RS485 or CAN internet communication interface( no need to add module)
13. Counting interface
14. 24 backup battery interface(can be connected with solar power)
Technical Parameters
- Working temperature(motor): -35℃~+60℃
- Rated voltage：DC24V
- Running speed：3s-10s
- Rated current：9.5A
- Rated power：250W
- No-load speed：2500rpm
- Rated speed：1800rpm
- Output Power：120N.m
- Relative humidity：≤90%
- Remote control distance：≤100M（in the open place）
- IP Degree：IP54
- Max length of arm:4.5M
Diagram of DC brushless mechanism
Product Size and Arm directions definition
Installation, commissioning and use
1、Equipment installation
1. Please select the correct type of barrier gate according to the specifications of the pace,and then fix the barrier cabinet with expansion bolts(refer to Figure 3).
After determined the position,the barrier gate foundation should be done according to the site conditions,and also make the cast-in-place basement for the non-concrete ground.
2、Select and commission spring
The spring is stretchable one and the specification is as follows:
Diameter 4.5MM red color
Diameter 5.5MM blue color
Diameter 6.8MM yellow color
Diameter 7.0MM white color
The spring length is subject to the actual product. Design changes will be notified separately.
3、Adjust the Position of Barrier Arm
To adjust the position of the arm (for example, after exerting excessive force), please take the steps as below:
1.open the barrier gate door and remove the cover
2.loosen the two fasten screws of the DZ-1 on the boom shaft with the M12’s Allen wrench, so that the boom can be re-positioned by hand.
3.adjust the position of the boom (horizontal position, as shown in picture 1).
4.Use the hexagonal wrench to tighten the two fastening screws (72 Nm)
4、Installation,dismantlement and adjustment of spring
The steps as follows:
please keep the boom in the vertical(boom open)position.
7.2.5.1 Unscrew the M8*140MM screw with a hexagonal spanner
7.2.5.2 Unscrew the M10 screw in the hanging scroll,Pull the spring plank open and take off the spring
The installation steps are just the opposite of disassembly!
5、Boom position adjustment
1 First please set the arm horizontally and vertically through regulation nut to lengthen or shorten the connecting rod.And then tighten M12 safety nuts.
2 To make the arm well balance,please adjust the M8*140MM spring regulating screw accordingly.
3 For the barrier gate with double springs,please adjust the two springs simultaneously.
4 See the above picture when the arm is shaking during opening and closing. When the arm is shaking during opening, that means that the spring is too tight, you can try to loosen the spring repeatedly. When the arm is shaking during closing, that means that the spring is too loose. You can try to tighten the spring multiple times.
6、Electrical installation, wiring diagram
1 All the electrical connections are done before delivery and please do not change it randomly.The necessity is to connect the AC220V power and grounding connection.
2 Traffic light connector:it can connect power no more than 40W.
3 Infrared photocells an-hit connector: connect the switch signal for receiver output.
4 Loop detector connectors:it supports both externally and internally loop detector(only one way can be chosen).
If external type is selected,just connect the switch signal for loop detector output.
If the internal type is selected,need connect the wire signal to vehicle detector wire interface.
5 Car parking system connectors: connect the system switch signal to this connector,then it can control the barrier gate operation.
6 Limit switch signal of up/down:with output COM,NO,NC,it monitoring the status of the barrier gate.
7 RS485 connector:after chosen the options RS485 module,it can manage MAX 15 pieces of barrier gates by PC software.
7、Function setting description
When setting the function, please press the menu button on the control panel, the digital tube displays H00-00 or H00-other numbers, we correspond to the function parameter table code to enter the required function parameter setting, for example, H00-00 is the open speed adjustment, and then press the confirm key Enter the parameter setting, display the number on the digital tube, then press the up or down key to set the required starting speed digits, and then press the confirm key to complete the setting of the open speed.
Other function settings are just as usual.
8、Error code
9、Learning type remote control
The remote control using special IC learning code remote controller, 418MHz wireless frequency, strong anti-interference, long remote control distance, that can up to 100meters in good weather, use easily and durable. The receiver of learning code remote control can store 16 different remote control codes, and support unlimited number of same code remote control. The external receiver learned the remote control within 5 seconds when power on,press the open/close key at the same time to complete the learning, and reset to continue learn when not complete. If repeat the learning, open the external receiver shell, there is a white button on circuit board, hold down 15 seconds to delete the remote control code, continue to learn or press the white button to learn.
Arm length speed comparison table
Service Items
1 One year’s free servicing is supplied(not including the arm);
2 Lifetime charged servicing is offered;
3 Technology servicing is supplied.
The following situations are charged for servicing(or changing):
1 Broken by the wrong installation.
2 Broken by improper voltage.
3 The surfaces of the system destroyed by wrong installation or use.
4 Broken by natural disaster.
5 Overdue.
6 Servicing items out of our promises.
Product Maintenance
1 Keep the barrier gate clean
2 Check the joints ever month in case of any loose parts.
3 Check the spring elasticity after the barrier gate running 3000 times.
4 Check the easily worn-out parts(like the spring,limit switch),every half year and renew it.
5 Remote control distance will be shortened or not work in case like big object screening,battery exhausting,extreme weathers.
Packing List
Appendix
